puch super reinforced racing swingarm

treats puch super reinforced racing swingarm - MAXI

$119.99

:HERE NOW!!

qty:

treats puch super reinforced racing swingarm for MAXI, newport, nostalgia, pinto, cobra etc. or for building a mini magnum or freespirit with shorter wheelbase!

features strong square tube construction (perfect for dirtpeds), three lower shock mount locations to adjust shock angle and ride height! Built in rear disk mount on right side for DIYers. fits up to a 2.75" wide tire (78mm width so maybe even 3"!!)

works perfect with the treats rear disk conversion mess o parts as well if you are feeling like fun times and adventures.

this has a caged axle design which requires a min 180mm length 12mm axle and sealed bearings and spacers for installation. if you absolutely MUST run cup and cone bearings, you can cut the rear tabs off opening the slots to the rear and run magnum/freespirit tensioners.

works with the stock puch pedal chain tensioner, drive chain tensioners, drum brake plate and rubber bushing, etc.

please note! this swingarm is WIDE, and will fit normal 28T pedal shaft sprockets, 30T will probably work fine if you happen to have that size, and over 30T you will just need to reshim the pedal shaft to get a hair more clearance on the pedal shaft sprocket side. seems like older 75/76 maxis have a 37T sprocket on the pedal shaft so if you have this size just plan on adjusting the shims to get it lined up perfecto. in our tests we were able to use the stock shims and adjust them without adding any additional ones.. but there have been so many maxis made in so many variations that you could possibly need an extra spacer or two. hey, its just what ya gotta deal with for maximum maxi tire width.

please note! this batch still has some sand blastin media leftover in the tubing from the production process that needs to be shaken out.. uh oh! sorry, it will not happen again we promise i think.

swingarm is 14" long (magnum is 1" longer) and weighs just under 4 pounds! gloss black powder coat finish!

new mounting bolts/washers

need a back mount plate for this bad boy? look no further

perfect length 12mm x 185mm axle

nice new supple n fresh swingarm bushings

rear disk parts for HOT DOGGERZ Puch Rear Disk

please search for the axles and 12mm axle spacers you need for your specific wheel (there are soooo many combinations!!!)

taco rating taco rating 5 of 5

5 of 5 Total Reviews: 3 give your taco rating here

0 taco eaters like this review

Beautifully crafted part!	August 15, 2025
taco eater : Frederic Chelminski from HOUSTON, TX United States

After breaking my 11mm axle with bicycle bearings, I had to improve things. This did the trick. Very well made! Congrats to the manufacturer for a job well done! Thanks Treatland!

Was this review helpful to you?

1 taco eaters like this review

It's girthy	October 7, 2024
taco eater : @Kickstandbois from Detroit, MI United States

I have this bad boi on my silver maxi. Is it sick!? You betcha! I have this comboed with the new treats rear disc kit and everything fit with minimal work. Super strong and not super heavy either, which is kinda surprising seeing that its waaaay stronger than the stock one. Can confirm, you want this on your maxi

Was this review helpful to you?

1 taco eaters like this review

Heavy Metal for your 1981	October 2, 2024
taco eater : Andy from Detroit

This thing is sick, I tested it for 2 years and did well over 500 miles on it with 0 complaints. Tons of potholes and jumping tons of speed bumps and catching air and it keeps trucking along and looks brand new still. I even run the treats rear disk party on it and it’s a full bolt on affair.

Very sick and a nice refresh on the MLM swingarm with 0 drawbacks

Was this review helpful to you?

treatland