puch 17" grimeca 5 star wheel SET - version 1

puch 17" grimeca 5 star wheel SET - version 1 - SILVER

$449.99

qty:

here's what ya get in this PARTYYY!:

1 of moped 12mm axle with spacers - 190mm ($17.00 value!)
1 of moped 12mm axle with washers and spacers - 165mm ($17.00 value!)
10 of M8 allen bolt - 20mm ($.49) ($4.90 value!)
4 of 6001 puch moped sealed wheel bearing + hobbit clutch bell!! ($43.96 value!)
2 of puch moped new 17" SILVER five star - RIM only!! ($250.00 value!)
1 of puch five star sealed bearing FRONT wheel hub - NUDE ($49.99 value!)
1 of puch 5 five star REAR wheel hub - NUDE!! ($74.99 value!)
2 of thick washer for axles - 24mm OD ($1.38 value!)

treat yerself with a pair of nice semi glossy luxurious SILVER 5 star rims complete with front and rear hubs, hub mounting bolts, sealed bearings with bearing spacers, and axles!

also possibly mount on peugeot, motobecane and more!!

so, the front and rear axles are both 12mm. you can use your stock rear brake plate with 80mm pads, or..

rear brake plate here!

you can grab a 94mm rear sprocket here and then some sprocket nuts n bolts here if you need em!

some original 80mm puch front brake plates are 11mm, most actually, so either drill yours out to 12mm or grab one here!

if its for puch, get some rear axle adjusters here!

feeling free? get a freewheel here!

it is highly suggested that if you want to ensure long bearing life, go with this sealed rear axle!!! it comes with one, but this axle promotes longer bearing life and is just better

these wheels come UNASSEMBLED so you have the fun of putting them together yourself! COO

comes with brand new sealed bearings. dont forget to do one bearing first, then the center spacer, then the other bearing on the other side!! ya boi!!!

then, install and bask in the glory of your 5 stars of fury

17" diameter
1.35" rim width
weighing in at exactly 4.00 lbs per rim (no hub of course). pretty dang light!

okay...and lastly as promised...

taco rating taco rating 3.5 of 5

3.5 of 5 Total Reviews: 2 give your taco rating here

0 taco eaters like this review

Does not fit. Murray puch	July 20, 2025
taco eater : Jeffery Dorris from Ellisville, MO United States

Even though I talked to customer support about trying to find Wheels that will install properly on my moped when I got them in. I cannot install the rear sprocket without drilling through the wheel hub. The space in between the wheel hub and where the bolt goes is too small. If you try to use a smaller bolt, you will not have enough thread to grab onto a nut if you try to flip the bolt around the nut hits the edge of the wheel hub before you can torque it all the way down. Even if you decide to drill through the wheel hub, you will only be able to get three out of six screws. The bolts that tighten the rim to the wheel hub and the threading itself is located over the top of three of the mounting bolts. Although I don't have another moped to test it out on, I cannot see this problem Not arising for other people do not buy unless you only want to use half of the fasteners and ruin the integrity of the hub by drilling through it.

Was this review helpful to you?

1 taco eaters like this review

Maize	August 6, 2021
taco eater : Maize from Saint Paul, MN

These are AWESOME! They are brand new! They go together easy and smooth! All the parts are included except brake plates.

Check out this video about them!
https://youtu.be/9mg8qpojzPA

Was this review helpful to you?

treatland