moped chrome clip on handlebars
moped chrome clip on handlebars
 



  $26.00


clip on size



qty:  
 
 
7/8" moped size chrome clip on bars for any moped you can mount them on. measure! or else! includes two bars and all the hardware needed to mount them think this is good on stock 103 forks, hmm perhaps? one of these sizes fits on STOCK magnum forks once you remove the stock headlight ears n replace them with aftermarket ones. i can't remember the size though n my measurin sticksss broke maxi EBR yessss puch, peugeot, motobecane, sachs, vespa, piaggio, honda, tomos, minarelli, garelli, derbi, yamaha, suzuki!

for some of these clip on bars the nut might not fit under the mounting hole so don't bend it out or anything drastic, solve your problem with some metric jam nuts.

taco rating taco rating 4.5 of 5 4.5 of 5 Total Reviews: 17 give your taco rating here

  0 taco eaters like this review
 
5 of 5 I love these bars! November 7, 2020
taco eater : Stretch Lamborghini from gainesville, FL United States  
I love these please keep em in stock! Not perfect but look best on vintage bike. I put em on Ducati cadets falcons and a 250 Monza. They fit wards riverside Benelli 250’s and 350’s. Fits Benelli fireball and parilla fantom. All without shims. You may need to find shorter bolts or file them down. And you need to cut down your head light ears. The only problem I had is the clamp on the bar was welded too close, so the nut won’t fit. You might have to file down the nut until it’s thin enough. I’m sure treats would take them back but can really wait? I also put a lock washer on the bolt side because it won’t go on the nut side. Prolly made in China what do you expect? They’re cheap! Then I tighten them really tight and I loosen up the triple tree until the fork legs move freely so I can straighten them! re-tighten the clamps and done! Also put em on Kawasaki AR80 and G3SS. I’ve paid a lot more for these bars on eBay and had the same mounting problems.

Was this review helpful to you?

  0 taco eaters like this review
 
4 of 5 Guess who's silly November 25, 2015
taco eater : Hi I'm Andy from Santa Cruz  
I ran these on stock Maxi/Swinger forks for a month or so. The 30mm fits without shims, but you gotta mount them backbreaking low, under the headlight ears.

One thing is they're hard to tighten down, and it's especially trickey to get that nut inbetween the bar and the clamp.

Was this review helpful to you?

  0 taco eaters like this review
 
5 of 5 32-35 great for Tomos Revival October 25, 2014
taco eater : Steven Whitright from Oakland, CA United States  
used the 32-35 on my Tomos revival front-end; fits well/looks good

Was this review helpful to you?

  0 taco eaters like this review
 
5 of 5 Clean look on a streetmate April 7, 2014
taco eater : Chance from bradenton, FL United States  
Bolted up great. Put in one side of bolts, spin it over tubes and then just slide other bolts right in from outside.  Almost went on to fast! The spacers made great paper weights for working outside also!

Was this review helpful to you?

  0 taco eaters like this review
 
4 of 5 Ergonomic Drop for little $$ October 24, 2012
taco eater : Arciero Rider from Chico, CA United States  
The bars look great on the bike, have just enough drop to be comfortable. The bolt holes needed some cleaning up because they were slightly undersize. Completely transforms the look of the bike, even though it had drag bars before.

Was this review helpful to you?

View All Customer Reviews