Return to motobecane tunŽ launch lever
 :
page of 1


  0 taco eaters like this review
 
4 of 5 pedals...hmmm Wednesday, June 11, 2014
taco eater : Matt Madden from Centennial, CO United States  
so i waited for this and i bought it...
was told it clears the pedals and it does but ya gotta work at it...
if you have pegs it probably bolts right up but if you have pedals you're gonna have to grind the sides on the part that slides on the crank quite a bit...
i'll work on it to make it work but i want to keep pedals, kickstand and side covers so it makes it harder for a dummy like me...

Was this review helpful to you?

  1 taco eaters like this review
 
5 of 5 fun off road!!! Monday, October 28, 2013
taco eater : SnowbyRider from Winnipeg, MB Canada  
Had this on the Moby 50v for a month or so now, daily rider, the silver bar needed some bending, but I was able to do it with a hammer and a vise easy so you can too!!! the hole for the pedal shaft is a bit snug, but nothing that can't be fixed with a bit of sand paper :D for the money it's one of the best upgrades you can do, cheap, and awesome.

Was this review helpful to you?

  0 taco eaters like this review
 
3 of 5 fab to make work Thursday, March 28, 2013
taco eater : John Palmer DPC from Bradenton, FL United States  
it is a great starting point but is just that a starting point . you will need to fab up some different linkage as the one it comes with is far too short

Was this review helpful to you?

  0 taco eaters like this review
 
5 of 5 Easy install AND IT WORKS!!! Tuesday, December 18, 2012
taco eater : Adam Pereira from castro valley, CA United States  
I added this to the ol 50V with an Av10.  Cleaned and greased my pedal shaft...slid right on!....made a couple 'custom' bends in the vice and on the rod and on it went.  For quick install, i went with the supplied hardware. Will it hold? Ha!! Has so far and is keeping my revs to the max.
THANKS!!!

Was this review helpful to you?

  0 taco eaters like this review
 
4 of 5 not bad but i needed to make a bigger plate Sunday, December 2, 2012
taco eater : brandon adkinson from Waukesha, WI United States  
after gringing down the sides of the  lever i got it to fit on my motobecane 7 the i needed a custom plate, but not bad if your willing to fab.

Was this review helpful to you?

  0 taco eaters like this review
 
5 of 5 Best Launch Lever Ever. Sunday, October 21, 2012
taco eater : Savoie from ON Canada  
Use this on all my pugs, I really only use the lever part in combination with threaded rod and two ball joint ends. Tomahawk tuning style. Gives a super power boost up hills so you can blast all your friends!

Was this review helpful to you?

  0 taco eaters like this review
 
4 of 5 Works fine on MBK Polini case Saturday, April 14, 2012
taco eater : Ian Templeton from Somerville, NJ United States  
I bought this for my AV10 Polini bottom end. foot pedal mounted to doppler pedal shaft with no problems, mounted to poini case it only one bolt used. drilled holes in both lever ends for cotter pins. had to bend a slight angle into the pedal end of the lever to get full insertion on both ends.

Was this review helpful to you?

  0 taco eaters like this review
 
5 of 5 awesome... Wednesday, March 21, 2012
taco eater : Whittier Domino from Whittier, CA United States  
well worth its value...for pugs at least....

Was this review helpful to you?

  0 taco eaters like this review
 
1 of 5 sorry for the bad rating but... Tuesday, March 20, 2012
taco eater : MBW from San Diego, CA United States  
This applies to motobecanes only: The lever didn't fit on the moby stock pedal crank. Needs to be bored out. There's also nowhere really obvious to mount it on the AV7 so it requires lots of fab. Better off just fabbing your own from scratch with the amount of work it takes.

Was this review helpful to you?