Review: List

Return to the original, crappy, 15mm bing intake

page of 3

0 taco eaters like this review

Look Man!	Sunday, April 2, 2023
taco eater : Philip Schaller from Cincinnati, OH United States

I just had to sand down the bottom, It fit well, It is a moped part? I have had no issues with this product. I have over 1000 plus miles on it. It is not crappy... It works! Fuck that grandpa shit, seriously. Vert de ferk?

Was this review helpful to you?

0 taco eaters like this review

Buy the #1 Grandpa	Saturday, December 19, 2020
taco eater : Valley Vintage Motorworks from Beaver Falls, PA United States

...nuff said. These are very cheaply made.

Was this review helpful to you?

0 taco eaters like this review

wut	Thursday, October 5, 2017
taco eater : Carbon Jawed from Cromwell, CT United States

I looked at it funny and it cracked.

Was this review helpful to you?

0 taco eaters like this review

priced appropriately	Wednesday, March 15, 2017
taco eater : rodney from san francisco, CA United States

its no MLM intake, but it gets the job done. use this on countless puch builds and it matches good with a 70cc piston port kit or just on stock. great with a 15 bing, even the clone seems to work fine. good if you dont wanna spend too much, otherwise id suggest the e50 or za50 mlm intake.

Was this review helpful to you?

0 taco eaters like this review

hahahaha	Wednesday, November 25, 2015
taco eater : Hi I'm Andy from Santa Cruz, CA United States

i mean, like it works. no sealing issues if you double up on thick gaskets or make some yourself. it did break though, just like the other reviewer. I put it on once, had to take it off to adjust something, put it back on, was tightening it and the base just crumbled.

It works, and would probably last a little while, but like, be soooo careful tightening it, and use 2 thick base gaskets.

Was this review helpful to you?

0 taco eaters like this review

It works fine now	Saturday, January 17, 2015
taco eater : Paul Selvidge from Sterling Heights, MI United States

This intake had a vacume leak when first installed.
I removed it, filed machined surface flat, good as new!!
Always use a new gasket, this intake has a a different print on the gasket compared to old intake.
It's cheep and works fine!
(Don't forget that O ring)

Was this review helpful to you?

0 taco eaters like this review

Surprisingly works, buy one!	Tuesday, August 26, 2014
taco eater : Matt from Colorado, United States

I bought this 15mm bing intake to match my 15mm Bing carb, and all I gotta say is.... it works!!

I was pretty hesitant before buying it due to all the bad reviews, but had no other choice so I spend the $12 and picked this bad boy up.

Once I got it in the mail I noticed it was made of pretty light metal, and I had to clean up/file the inside a tiny bit. But once I set it up with my E50 it bolted right on and I've had zero air-leak issues!

Was this review helpful to you?

0 taco eaters like this review

so-so	Saturday, August 9, 2014
taco eater : carl withak from henrico, VA United States

used an open end wrench, lined up fine, nothing to complain about.

Was this review helpful to you?

0 taco eaters like this review

Do not buy	Friday, June 28, 2013
taco eater : Paul Handlen from easthampton, MA United States

In my time buying items from treatland I haven't found many things to complain about, until now. This is probably the worst intake I've ever purchased. The right side hole is drilled so far inside that its impossible to get a socket around it without grinding away some metal. It seats suuuuper poorly (even with 3 stacked gaskets it leaked like a civ). when I finally managed to seal up the carb side (a process that involved an o-ring and a shitload of yamaseal) the base snapped in half when I tried to torque it down. It didn't even get to full spec (70ft/lbs), literally crumbled at about 50 ft lbs. Forget this piece of junk. Don't waste your time or money.

Was this review helpful to you?

0 taco eaters like this review

Super light, poor machine, misaligned	Saturday, September 22, 2012
taco eater : b0tt from Oakland, CA United States

Looks a little better than my last 15mm Bing intake that I bought back in 2006 from 1977mopeds (probably still made by the same people?) but it's still super light and fragile feeling. The hole is at an angle and does not line up well with the cylinder intake.

The fit on the carb was too big so it took a lot of sanding to get it to fit. At least there won't be an air leak there though right :)

Took a lot of dremeling and lapping to get this thing right.

Was this review helpful to you?