Review: List

Return to puch E50 & minarelli V1/V1L clutch puller

page of 3

0 taco eaters like this review

NC50 Tool Too!	Friday, March 27, 2026
taco eater : Dakota Josh from Sioux Falls, SD United States

Worked for my NC50! Had to do some surgery on the ol girl and this tool came in handy. Good price too!

Was this review helpful to you?

0 taco eaters like this review

Clutch puller works but beware	Saturday, February 21, 2026
taco eater : Chase Havoc from San Antonio, TX United States

This worked fine for my Ciao engine, but then I used it on a Minarelli v1 and had bad luck. The smaller M6 screws stripped out while pulling the clutch. Lots of people have this issue apparently with the V1 clutch. I had to tear the top of the clutch off and then painstakingly weld tabs to the bottom of the clutch plate to get the thing out. I did end up buying some replacement M6-1.0 x 50 stainless steel screws to use in the future after ruining my black ones. Stainless is much more durable anyway.

Was this review helpful to you?

1 taco eaters like this review

Works on my 1978 Honda NC50	Saturday, September 13, 2025
taco eater : Belingo Sanchizmo from APO, AE United States

If your ratchet isn't doing the job, stop and pick yourself up an impact drill. Im telling you, my stock clutch potato-chipped under the brutal force my scrawny arms inflicted on the center-bolt of this thing. The drill on this puller removed that wavy centrifugal bastard in a second. Use the right tool for the job!!

Was this review helpful to you?

0 taco eaters like this review

Works on my Express II	Tuesday, March 11, 2025
taco eater : Stevie wingwang from Channahon, IL United States

Looking everywhere for a clutch puller, finally found treatland. Description said it'll work on a na50 engine and it did. Waited a week for a tool that I used less than for 3 minutes. Excellent job treatland!!!

Was this review helpful to you?

1 taco eaters like this review

Worked for my express.	Thursday, June 17, 2021
taco eater : Anonymous Person

I had to steal the exhaust nuts to thread onto the Allen keys since my clutch doesn't have threaded inserts. I put it on, cranked it until it made a sickening ker-chunk and popped the clutch right off.

Was this review helpful to you?

1 taco eaters like this review

Also works for Land Rover defender steering wheels	Monday, December 21, 2020
taco eater : Naplm00 from bay bay bay

Had one for eons from treats, also happens to fit my defenders steering wheel same bolts and everything

Was this review helpful to you?

0 taco eaters like this review

Busted my old crank	Thursday, October 5, 2017
taco eater : Jacob Andrew Carbon Jawed Dodge from Cromwell, CT United States

One of the hex screws was chewing up my clutch threading; had to reinstall a couple times before it stuck and my clutch went flying. WARNING!!! It blew through my stock e50 crank threading clutch side. Luckily I was going to replace it.

Was this review helpful to you?

1 taco eaters like this review

Pulls clutches	Friday, January 29, 2016
taco eater : Wesley Brown from Austin, TX United States

That it does.

Was this review helpful to you?

0 taco eaters like this review

Works pretty well	Sunday, October 18, 2015
taco eater : Hank the Gender Queer Toptank from Portland, OR United States

Made a few before using this one and realizing my clutch had fused to the axle. this thing shredded the axle end, so, i guess it's pretty sturdy

Was this review helpful to you?

0 taco eaters like this review

As Advertised, BUT	Wednesday, August 26, 2015
taco eater : Marc from CT United States

Puller fit well, however quality is a little cheap. On the main threaded screw the threads were pretty messed up at the end and I had to clean them up prior to use. Otherwise this dank puller yanked that clutch straight offffffffff. Also, used on Puch E50

Was this review helpful to you?