Return to motobecane RUBBER motor mount bushing - large
 :
page of 2
Click to see more items


  0 taco eaters like this review
 
1 of 5 engine mount bushing failure fix Wednesday, September 20, 2017
taco eater : Mocninja from Milwaukee, WI United States  
cheap

Was this review helpful to you?

  0 taco eaters like this review
 
5 of 5 They do the job, but will rip Saturday, July 15, 2017
taco eater : Dan from Moreno Valley, CA United States  
These are gonna rip no matter what, especially if your bike is kitted.

I soak mine in ND30 oil until im ready to install

Was this review helpful to you?

  1 taco eaters like this review
 
3 of 5 stock cylinder motors Saturday, November 2, 2013
taco eater : Anonymous Person from Salem, MA  
not bad for a resto or 50cc build, 75cc not so much.

Was this review helpful to you?

  0 taco eaters like this review
 
1 of 5 Failure Saturday, May 11, 2013
taco eater : chad vardas from westminster, CO United States  
Ya no I got them in and they were done less then a hundred miles need to find some quality ones from somewhere

Was this review helpful to you?

  0 taco eaters like this review
 
5 of 5 why such a low review? Sunday, March 31, 2013
taco eater : John N from Brooklyn, NY United States  
I removed the old ones with a hacksaw and beat them out with a hammer. and then pressed these in with a ball joint tool. They were a pita to get started in straight but once they were in and bolted the engine in..wow...what a difference. I was used to my engine swaying left and right up to an inch at idle.....no more!

Was this review helpful to you?

  0 taco eaters like this review
 
1 of 5 Bushing Fail Wednesday, April 4, 2012
taco eater : Delmer Totten from Los Angeles, CA United States  
These motor mounts are the worst. Don't waist your time and money if if your running a kitted Mobi. Looking for a tutorial on how to make my own.

Was this review helpful to you?

  0 taco eaters like this review
 
1 of 5 cracked up Wednesday, August 31, 2011
taco eater : motothrowbacks from new bedford MA  
can't handle a kitted engine, failed in less than 30 miles.  I had to try them tho

Was this review helpful to you?

  1 taco eaters like this review
 
1 of 5 $5.00 worth of torn up rubber Tuesday, May 24, 2011
taco eater : Willie from Sarnia,Ontario,CANADA  
these are horrible on a kitted motor.. torn to shreds in 30 km, changed mounts twice in two days then went back to homemade mounts.
they may be the thing for stock but a waste of $$ to me.

Was this review helpful to you?

  2 taco eaters like this review
 
4 of 5 Simple solution, "Rebound Washers" Friday, May 6, 2011
taco eater : The Twisted Tuner from Peg City, MB, Canada  
On my stock mounts for 50v, I used Lagre fender washers on the outsides.  They are larger than the "metal cup" the mounts sit in.  But the center insert is long enough to stop washer from rubbing on the rubber.
This creates a "Rebound Washer" that will give you a second chance the next time your doing 1 mile wheelies!!!  Ya.  
Dunno may help.

Was this review helpful to you?

  0 taco eaters like this review
 
2 of 5 didn't last Sunday, April 17, 2011
taco eater : mikeboyd from fromsftoaustin  
mobys just vibrate too dang much. I put these in a little over a month ago and the variator side mount is already toast.

Was this review helpful to you?

   
  Click to see more items