Review: List

Return to honda hobbit stocko shocko extremo 60.2cc kit

page of 5

0 taco eaters like this review

Honda 1978 pa50 this kit is well worh the money!	Sunday, October 13, 2024
taco eater : John Sullivan from Saint Clair, MI United States

I heard good and bad about this kit. well i'm hear to tell you I took a bone stock honda pa50i that ran great,only went 15 mph! i installed this kit, super easy I used 2 gaskets between the block and cylinder for a little extra thiskness. I did have the adjust the idle a little. but other then that it works great now it will do 25mph no problem! this kit made me a very happy pa50 owner!!!

Was this review helpful to you?

0 taco eaters like this review

Good Value	Friday, May 5, 2023
taco eater : Mario Termine from Blacksburg, VA United States

Piston hits head. Added a second base gasket and it fixed it. Doesnt seem to leak yet?

Must drill and tap the decomp port. I used an m6 tap and set screw with red loctite.

I didn't trim the fins because on the Express II NC50 you can fill the oil from the front of the case as well so the side fill port isn't needed. But if you have the single speed you'll probably need to trim.

Running it with a stock pipe and a Dellorto 15 with a cone filter, 70 jet after break in seems to do nicely at 2k feet elevation. Stock pipe is too restrictive to see any performance improvements so Im still only hitting about 27mph top speed. But eventually I will throw a pipe on it. This 60cc kit was about the same price as a stock replacement so I figured why not. Overall for 80 bucks it's pretty good. Hopefully it lasts a while.

Was this review helpful to you?

1 taco eaters like this review

Besides the needed modifications I love it!	Thursday, March 30, 2023
taco eater : John Stevens from Worcester, MA United States

For my 1980 Honda Express NC50 fin cutting was of course needed to clear the frame and the tranny oil fill plug. Also plug the decomp hole. Also depending on your year/model you'll NEED a metal base plate spacer (or maybe just a thicker base gasket?) if using the stock head like I am otherwise the piston will hit the head!!

But now i'm impressed great low end take off, and NO PROBLEM with steep hills all over my neighborhood!! Had it near 30mph and this is with the stock original muffler!! I'll have to try out the MLM "stock like" pipe next!!

Was this review helpful to you?

0 taco eaters like this review

Fantabular	Wednesday, June 8, 2022
taco eater : Rabies Matt from Winnipeg, MB Canada

Really a great bang for buck! it even has 49.9cc on the side so you can confuse and amaze your homies.. I suggest one of the metal hobbit spacers for the base.. I went with .8mm spacer, and 2 paper gaskets.. everything lines up nice.. running stock head, she rips! UPDATE: SHE REALLY F'n RIPS!! If you bolt on with stock or jammy pipe and stock carb, yea is great bang for buck, itll rip... But if you empty that duct tape wallet and splurge on the VM20 carb party, along with a proma pipe, and dremel the crap outta your stock reed block/intake block thing that attaches to the MLM intake, you will be ripping PAST THE RIPPERS! YOU WILL DOUBLE THE RIPPAGE FOR ONLY 4X THE PRICE! Just friggin do it. Dont be a scaredy cat. Who cares about water bills?... Wheelie life sucka.

Was this review helpful to you?

2 taco eaters like this review

1983 Honda NC50	Saturday, June 4, 2022
taco eater : Jason Rosenthal from Red oak, TX United States

This doesn’t plug and play. Fins have to be cut. Piston hits head. Will update if I get it to work.

Was this review helpful to you?

0 taco eaters like this review

Great upgrade	Wednesday, May 11, 2022
taco eater : Birch from CA United States

Bike: Honda Hobbit PA50

This kit definitely got me ripping nearly 45 mph with the honda hobbit "jammy" performance exhaust pipe. Required a bit of air/ fuel mix adjustment from the stock cylinder using the 16mm-ish honda hobbit pa50 clone carb. Used two head gaskets to give a little extra thickness as was suggested in other comments.

Con: went so fast my speedometer died after an hour of riding. Did not come with M6 studs for exhaust mounting, and seemed to need longer studs than what was on the stock cylinder.

Was this review helpful to you?

0 taco eaters like this review

Needs thicker base gasket	Wednesday, November 24, 2021
taco eater : Brian Ferguson from Ann Arbor, MI United States

Piston hit the head with the linked to gasket set. Adding two more head gaskets was enough to fix that problem, but of course it leaked, so just go with a thicker base gasket.

Was this review helpful to you?

0 taco eaters like this review

Express II na50	Thursday, September 9, 2021
taco eater : Roy Peters from West Bloomfield, MI United States

Installed with stock carb with a 85 jet and stock exhaust. I did put an extra gasket at the case as the piston was very tight @ the head gasket. Trimmed 3 fins with a dremmel to drain the trans oil. Picked up 3 mph and better uphill speed.

Was this review helpful to you?

1 taco eaters like this review

Good upgrade even if going for sleeper look	Thursday, June 17, 2021
taco eater : Anonymous Person

Kit went together just fine. Has a lot of sharp edges though, and I had to trim the fins (as expected) and the decomp port was sorted with a chunk of a bolt. Has HIGH compression. Besides reeds the bike is basically stock. Throw on the MLM next level pipe and paint the shield the correct color and you have a nice sleeper.

Was this review helpful to you?

1 taco eaters like this review

Has potential!	Friday, April 3, 2020
taco eater : Eds Moped Shop from Omaha, NE United States

With the right amount of work, I was able to get this kit up to 55mph!
I decked the cylinder 2mm, opened and raised the exhaust to 175*. 2mm base spacer/gaskets. 44mm Treats custom cut Puch head(no gasket). 19mm PHBG. 0.35” reeds. CrankPipe. Stock points!

Was this review helpful to you?

treatland