Return to yet again a moped voltage regulator/RECTIFIER
 :
page of 1


  0 taco eaters like this review
 
4 of 5 Saves Bulbs Thursday, August 3, 2023
taco eater : Dangertooth from Okanagan Falls, BC Canada  
TBH I have no idea what it does, how it works, or how to wire it.

I keep messing with it until I stop blowing bulbs. I've put these on 3 different bikes with points, and been happy.

Was this review helpful to you?

  0 taco eaters like this review
 
2 of 5 Hit and miss Friday, October 25, 2019
taco eater : Anonymous Person from brooklyn, NY United States  
Bought 3 of these. 1 worked, 2 didn't ¯\_(ツ)_/¯

Was this review helpful to you?

  1 taco eaters like this review
 
5 of 5 Ima keep it a hundo with you. Sunday, June 2, 2019
taco eater : Jonathan Feldman from Oakland , CA United States  
I've had two of these and neither of them regulated correctly with the wiring diagram suggestions listed below.
I tried every pin combination humanly possible and none of them functioned as a 12v regulator. Maybe some are internally different than others? Who knows

But good news, your boy Jon has cracked the Da Vinci code. There was a wiring diagram that used to come with these that no longer exists. I was lucky enough to find it on MA.

/====(4)
/  ====(3)    
O =====::]
\  ====(2)      Ground
\====(1)        Light coil hot lead / lighting wire harness.

Pin 2 gets grounded and then pin 1 is both your stator lighting coil hot lead and the wire that is gonna go to whatever harness you have for your lights. So pin 1 is gonna have 2 wires theoretically. Or maybe 1 wire if your lighting wire harness is already spliced with the stator lighting coil wire.

Sorry if I worded that poorly. It'll make sense once it's in front of you I swear.

Was this review helpful to you?

  0 taco eaters like this review
 
2 of 5 It's a regulator that regulates, but doesn't recti Monday, May 27, 2019
taco eater : Jason from San Antonio TX United States  
I was only able to get AC out of this thing, produced no DC voltages (verified with both auto-ranging DVM and O-scope).

Borrowing a bit of artwork from a previous post, I tried the following combinations on an AV-7, Le parties CDI, 1/4 throttle.  YMMV.  All voltages identified below we're measured as positive (+) values.

Config numero uno (lighting coil on pin 1):

/====(4)[ 0
/  ====(3)[- 12.7 VAC
O =====::]
\  ====(2)[ 6.5 VAC
\====(1)[- lighting coil

Config numero two-o:
/====(4)[ 0
/  ====(3)[ 8.7 VAC
O =====::]
\  ====(2)[ lighting coil
\====(1)[ 8.7 VAC

Config ##3:

/====(4)[ 0 volts
/  ====(3)[ lighting coil
O =====::]
\  ====(2)[ 6.4 VAC
\====(1)[ 12.6 VAC


Config ##4:
/====(4)[ lighting coil
/  ====(3)[ 0
O =====::]
\  ====(2)[ 0
\====(1)[ 0

Configs #1 or 3 are probably what you'd want if you're looking for a regulator.  Guessing pin #2 is for battery?
Again, YM(and V)MV.  NO DC (rectified) output :(

Was this review helpful to you?

  8 taco eaters like this review
 
4 of 5 Is okay. Saturday, September 2, 2017
taco eater : arty party from Portland, OR United States  
How to wire as regulator only [ground mounting hole (O]:


 /====(4)[
/  ====(3)[- Yellow wire in from stator
O =====::]
\  ====(2)[
 \====(1)[- Red wire out to lights

Was this review helpful to you?

  0 taco eaters like this review
 
4 of 5 Tacos Wednesday, September 18, 2013
taco eater : Hugh Goldspiel from San Jose, CA United States  
I put this on my Kinetic.
Works good. No problems.

Was this review helpful to you?

  1 taco eaters like this review
 
1 of 5 dud Saturday, August 17, 2013
taco eater : moped man from portland, OR United States  
on my vespa it didn't work so I sent it back to treat the other one that looks like this that is out of stock works great on my ciao im waiting to get another

Was this review helpful to you?

  8 taco eaters like this review
 
5 of 5 YEU Saturday, October 22, 2011
taco eater : ∫≈▲Chin▲ϟhop P†pe from Youngstown, OH United States  
Plug it up, no mo light woes, shit works. Smoke dope...drink Busch.

Was this review helpful to you?