Return to moped 12mm axle with spacers - 190mm
 :
page of 1


  0 taco eaters like this review
 
3 of 5 You are going to need some proper spacers Friday, August 15, 2025
taco eater : Frederic Chelminski from HOUSTON, TX United States  
I was able to use the long spacer between the two Bearings, but the others were not the right length. This is TOTALLY understandable. The quality of the Spacers was pretty bad too. FYI: you will likely need to obtain a variety of spacers and experiment, or learn how to accurately measure what you will need. You may even need a machinist to make good spacers like I did.


Was this review helpful to you?

  0 taco eaters like this review
 
3 of 5 Center spacer is too short Sunday, April 27, 2025
taco eater : Steve from Lake Mary, FL United States  
I bought this for my Puch spoked wheel sealed bearing conversion. However the center spacer is about 1/4 too short causing the bearings to bind when tightened.

Was this review helpful to you?

  0 taco eaters like this review
 
5 of 5 kevin spacey Friday, November 3, 2017
taco eater : rodney from san francisco, CA  
so many spacey spacers it helps when youre setting up a wheel. has a nice squared off end so that you can hold the axle in place instaed of marring the threads when you need to loosen a tricky axle nut or tighten it. used these on tons of bikes, good cheap simple solution.

Was this review helpful to you?

  0 taco eaters like this review
 
1 of 5 bent Tuesday, March 14, 2017
taco eater : broke ass hobbit from Riverside, RI United States  
axle came bent out of the box. splendid

Was this review helpful to you?

  0 taco eaters like this review
 
5 of 5 Great fit for Peugeot Rear! Saturday, January 24, 2015
taco eater : A.T. from Southampton, MA United States  
perfect length for pug rear. snug fit in bearing as well. got one that looks like the threading on one side ran almost into the shaft, so its a little flared and will only go through things from the other end. snug tho!

Was this review helpful to you?

  1 taco eaters like this review
 
5 of 5 Great 4 Garelli Wednesday, July 23, 2014
taco eater : John Fuller from Yardley, PA United States  
Perfect for my 85 Garelli conversion to sealed bearings.  Had to add a couple washers but spacers were just what i needed.

Was this review helpful to you?

  4 taco eaters like this review
 
4 of 5 Works great for sealed snowflakes Saturday, March 30, 2013
taco eater : Samuel Drupiewski from El Dorado Hills, CA United States  
Used these on my maxi with sealed bearing snowflakes. The long center spacer cannot be used for the conversion. It's too short and would put the bearing too far inside the rear wheel to be effective. Instead, you must use the longer axle spacer treats sells individually. Know what I'm sayin'?!

Was this review helpful to you?

  0 taco eaters like this review
 
5 of 5 k10's Monday, March 18, 2013
taco eater : Taylor Duncan from Columbus, OH United States  
oh you got k10's? good, they're all gone now I think. this axle works perfect for your conversion

Was this review helpful to you?

  2 taco eaters like this review
 
5 of 5 fits Sunday, February 12, 2012
taco eater : Aaron Fowler from Richmond, VA United States  
bought this to mount a Tomos Mag to my Scorpion swing-arm (minarelli/morini). snug in the wheel, spacers to center it, and i only need to file down the brake hub nub.

Was this review helpful to you?