Return to puch con rod bushing
 :
page of 1


  0 taco eaters like this review
 
3 of 5 factory tools anyone? March 28, 2014
taco eater : Deadped Ryan from Franklin, TN United States  
There's a factory tool for reaming these after they're pressed in... I have it and haven't done a bushing on a crank yet, but when I do, I'll post back.

Gotta ream yo!

Moped people love to not read directions.

Was this review helpful to you?

  0 taco eaters like this review
 
5 of 5 on an a3 September 27, 2012
taco eater : Anonymous Person  
did anyone below ream their bushing to proper spec after installing their bushing?

I highly doubt it. No jumping the gun, ya can't just press it in and expect it to be the perfect size.

to those who did ream it properly and have one on a kitted setup, anything past 8500 rpm is liquification zone. (needle bearings ftw)

they are fine if you know what you are doing.

Was this review helpful to you?

  0 taco eaters like this review
 
1 of 5 junk June 12, 2012
taco eater : Z from oHIo  
Worked okay for almost 1000 miles on stock 50cc, but got obilterated somewhere around 900mi. all that was left was brass coloured sluge. piston and cylender came out unscathed.

order some more good ones guys!

Was this review helpful to you?

  0 taco eaters like this review
 
1 of 5 super sketchy October 6, 2011
taco eater : Raniel Dantic from Sanford, FL United States  
Installed correctly. Drilled holes and reemed the thing. It lasted maybe 3 months of daily commuting on a kitty till it disappeared. All that was left was a golden glaze. Piston and cylinder came out surprisingly unscathed.

Was this review helpful to you?

  1 taco eaters like this review
 
1 of 5 Kitted an A3 June 23, 2011
taco eater : Clay Anderson from San Francisco, CA United States  
I picked up this bushing but it had no oil holes. So I drilled 2 and popped the old bushing out. Pressed this one in with the C clamp method and everything seemed to line up. Worked well for less than 100 miles before I broke down and found my spark plug covered in melted/disintegrated brass and the piston had fragments too. The cylinder looks fine and a bit of the lower piston ring broke off. Pulled the semi-fused bushing and con rod out to find fragments of brass and a barely recognizable bushing. Running the 45mm 70cc alukit by the way.

Was this review helpful to you?

  1 taco eaters like this review
 
1 of 5 sh*t April 21, 2011
taco eater : Bandito from orlando  
pressed it in, drilled the hole, then broke it in for about two days just starting it up and putting around the hood, went on a 8mile or so ride seemed great. Next day on the way to my buddies it spun and seized my arisal kit, piston had a piece missing along with a broken ring but the cyl is still perfect thank god, so i ethier got a clapped out con rod or this bushing sucks!!!   or Both

Was this review helpful to you?

  2 taco eaters like this review
 
5 of 5 Yo! August 3, 2010
taco eater : Anonymous Person from westmont, IL United States  
The new batch is all good! It pressed in nice and tight. Dont forget to drill in the new oil hole.

Was this review helpful to you?

  6 taco eaters like this review
 
5 of 5 this is what you use when you kit an A3 Tomos October 29, 2009
taco eater : matt Vassallo from Largo, FL United States  
this is the bushing you get when you kit an A3 Tomos


once you install it you can put any puch or tomos a35/a55 kit on you want!!!  GILA?  YES   metra80? YES   POLINI?  YES



Was this review helpful to you?