Return to dellorto SHA 14.12 carburetor with lever choke
 :
page of 1


  3 taco eaters like this review
 
5 of 5 This fits Tomos A3. Maybe get a cable choke 15... November 11, 2014
taco eater : Byron from Port Coquitlam, BC Canada  
For Tomos A3:
Get the bendy cable thing that screws in the top.
Get a SHA A3 intake.
File your engine bolt frame holes about 1mm to lower the engine. This will fit and you'll be able to remove it without dropping the engine if you remove the intake first.
You may need to file/drill the throttle slide to make your knarp fit.
Consider a cable choke version because you can't really use the lever choke with side panels.
Consider a 15 SHA because this is still kinda small.

Awesome carb for stock-ish setup, super reliable and easy to clean.

Was this review helpful to you?

  3 taco eaters like this review
 
3 of 5 great carb for motobecane 7 September 7, 2014
taco eater : chad salter from san francisco, CA United States  
Installed with a 1mm shim right to my stock intake !
You'll need a straight banjo fuel intake.
I had to hammer a small 1/4 in dent in my frame, so the carb would fit and be aligned and level. Nice and snugg... the manual choke doesn't disengage unless u pull the air screen and push it back up. . So i took it apart and ground off the hook . So it's fully manual now..  bike started right up. Sweeet...

Was this review helpful to you?

  0 taco eaters like this review
 
5 of 5 excellent and consistent April 29, 2011
taco eater : heywood jablome from pa  
works great, its an sha, what else is there to say?


50v- 56 jet, 53 with the stock filter
motorized bike- 63 jet no filter


Was this review helpful to you?

  1 taco eaters like this review
 
5 of 5 I put one on a 1975 Motobecane November 21, 2010
taco eater : Micheal Hernan from North Benton, OH United States  
It works fine! The old Gurtner could not be made to work.

Was this review helpful to you?

  5 taco eaters like this review
 
4 of 5 easy to use/work on July 22, 2010
taco eater : Stefan Didizian from Huntingdon Valley, PA United States  
easy to install. Use a 1mm shim for the stock motobecane bendy intake. With the lever choke you can rip off the choke cable from the old carb and never look back! get around 53 for a moby 50v

Was this review helpful to you?

  9 taco eaters like this review
 
5 of 5 replaced Encarwi (Batavus HS50) November 4, 2009
taco eater : Dimitri Tripodakis from Needham, MA United States  
I replaced the Encarwi carb on my otherwise STOCK Batavus HS-50 (25mph version). To do the same, you will need a shim for the manifold since it is 2mm smaller in diameter. The throttle cable will "plug and play". The choke cable you will need to toss or find a way to make it work. The clearance for the fuel line is tight but it can fit with no problems or alterations. Finally, I used a round file to open up the inner diameter (ID) of the stock manifold to match the ID of the "out-take" of the Dellorto 14.12. The HS50 now runs consistently well using a #61 jet (on the rich side I believe). I haven't clocked the mph but it definitely feels faster overall. Not much difference in acceleration as in cruising/top speed. Im glad I replaced the stock carb with this one, the moped feels much more reliable. And of course, thanks TREATS for your super fast shipping and moreover, your....well, to say it simple, you guys are nice people.

Was this review helpful to you?