MLM tomos a55 vm18 + PHBG intake
MLM tomos a55 vm18 + PHBG intake
 



  $49.99

 :HERE NOW!!

qty:

 
 
motion left mopeds 18mm clamp style intake for tomos a55 with a mikuni vm 18mm carburetor!

this intake will fit on stamped tomos frame only, with the stock or airsal cylinder. you must use allen bolts to attach the intake. it can be used on the left or right side of the bike depending on your petcock position.

to clarify DOES NOT FIT tube frame A55 models!!!

can you believe it? i can't! finally another option for the a55! and on top of that it's made by MLM!!!!!

NOTE! the fitment on these intakes has been changed so that you no longer have to grind anything down...should be smooth sailin!

shoots the carb out to the side aka 90degrees from the original carb mount location

oh this just in! this intake will also work with a dellorto PHBG clamp style carb with the 1.5mm shim and the spigot style!

taco rating taco rating 4.5 of 5 4.5 of 5 Total Reviews: 7 give your taco rating here

  2 taco eaters like this review
 
5 of 5 Made my own, but its worth the $$ if you can't September 11, 2017
taco eater : Brandon weiss from BROOKLYN, NY United States  
I made my own intake from bike handlebars and flatbar, but if you are not handy like that i suggest going with this intake, ESPECIALLY if you have the A55 Airsal kit. If you are wondering why the Airsal kit is slow, its because you are using the stock A55 intake. This will wake up the bike like you wouldnt believe. Did some tests over 100 ft- A55 airsal w/biturbo, stock intake, 17.5 phva: 19mph
A55 Airsal w/biturbo, 18mm intake, 17.5 phva: 26mph.

Was this review helpful to you?

  2 taco eaters like this review
 
3 of 5 WHY DOES IT NOT FIT A STREETMATE ? February 27, 2016
taco eater : SAMSON from el cajon , CA United States  
WHAT MAKE THIS NOT FIT AND WHAT CAN DO TO MAKE IT FIT MY A55 AIRSAL 70 ON STREETMATE. IF ITS NOT DOABLE WHAT ELSE CAN I DO ANY OTHER INTAKES MATCH ?

Was this review helpful to you?

  2 taco eaters like this review
 
5 of 5 2011 Tomos ST/Airsal/17.5 mm Dellorto PVHA September 30, 2015
taco eater : frodarphotography.com from Laurel, MT United States  
Estoril Sidebleed exhaust, 22th rear. then added this intake. Goes on either side, if on left(must switch fuel petcock) you can install on cyl. first. On right you have to put it on after you put cly. on. Use ball hex wrench. Compared to stock manifold, better idle, and more power throughout rpm range with MAJOR boost at 35mph. (like NOS!) Sticks straight out side, use short filter or velocity stack. 35mm on PVHA. I will do a video soon for utube installing it.

Was this review helpful to you?

  1 taco eaters like this review
 
5 of 5 uhm, yes please. September 4, 2015
taco eater : Conan from Myrtle beach, sc  
If you have a kit and bigger carb, you're going to want this. first off it looks awesome and helps your ped rip. it fit right on perfectly, i had to use a round head allen key to tighten the right side. you'll thank yourself for getting this.

Was this review helpful to you?

  1 taco eaters like this review
 
5 of 5 yes May 1, 2014
taco eater : Stephen Pamboukes from Portsmouth, NH United States  
i'd say yes, you wanna run this on an Airsal kit.  watch out for tight powdercoat.  allen bolts with loctite!

Was this review helpful to you?

View All Customer Reviews