mikuni vm 18mm clamp style carburetor
mikuni vm 18mm
 



  $118.75

 :HERE NOW!!

qty:

 
 
mikuni vm 18mm round slide clamp style carburetor, perhaps one of the most revered of all carbs for its flawless quality and performance.

clamp style carb so you will have to have an intake that works with this, or have a special one made...

since this is a clamp style you cannot over tighten the clamp otherwise you risk snapping the clamp, just snug it up is all you need!

comes with a fancy lever choke, cool idle screw that sticks out a bit for easy access and an air mixture setting.

screw top for easy access for needle and cable installation.

It is HIGHLY recommended you upgrade the shim these come with to one of these. They fit better and you end up with the same ID (23mm).

uses 32mm (PHBG) air filters except the ones that are screw type!

uses mikuni large hex jets and idle jets

uses phbg clamp style shims! this means you can use it on any clamp style phbg intake!

comes with a 70 main jet, 30 idle jet, needle #4F18, needle jet #145650-0, and slide cutaway #1.0

ID = 23mm (intake clamp)

OD = 32mm (air filter spigot)

taco rating taco rating 5 of 5 5 of 5 Total Reviews: 36 give your taco rating here

  0 taco eaters like this review
 
5 of 5 Sucks in a good way September 7, 2023
taco eater : Urban Spaceman from Bloomington, IN United States  
The Puch Maxi i bought from a friend has this on it. Seems perfect for the 65cc Metrakit that was added to it. Probably upjetted so I recommend buying some new jets in case. Next time I take it apart I'll try to list the numbers so folks can know!

Was this review helpful to you?

  4 taco eaters like this review
 
5 of 5 Excellent October 2, 2021
taco eater : Christopher Morris from Shreveport , LA United States  
I got this carb to upgrade my motorized bicycle and this thing makes my powerband hit so hard way harder than my stock carb definitely recommend for a 66/80cc motorized bicycle motor

Was this review helpful to you?

  0 taco eaters like this review
 
4 of 5 Good Carb, Figuring it out June 29, 2020
taco eater : Francois Labat from Campbell, CA United States  
Installed the carb with the MLM intake for AV7 moby.
I had to remove the VM18 rubber gasket at the intake, for the shim to fit. Now it holds on and doesn't fall off.
I'm having issues with the carb overflowing at high RPM, will report back if I find a solution.

Was this review helpful to you?

  3 taco eaters like this review
 
5 of 5 VM18 Customer service May 10, 2020
taco eater : Brian Lestage Sr. from Seal Rock, OR United States  
Best customer service in the world! Broke the clamp on my VM18, asked if it was under warrantee. They shipped me a new carb body and didn't even charge me shipping! Not expected at all. No hassle, no asking questions, just replaced it and shipped it out right away. If I need parts, I'm looking here FIRST! Thank-you Treatland, you're the best!

Was this review helpful to you?

  1 taco eaters like this review
 
5 of 5 Buy it September 20, 2019
taco eater : Justin Ritchie from Dayton, OH United States  
Well made. Easy to tune.
Main jet is only used during 3/4 to full throttle. Needle controls the gas at about half throttle. Idle jet is for idle and about 1/4 throttle.
Spring has alot of tension too so the throttle snaps back into place when u let go.
Fancy.

Was this review helpful to you?

View All Customer Reviews